HYDRA Tecno Pop 5 Frp Lock Remove With Hydra Tool (1 Viewer)

-------------------------------------------------------
To Enable BROM  Mode :
     Method 1    - Bootkey (Vol + - Power) or any combination
     Method 2    - Enable Preloader to brom(crashing Method)
     Method 3    - Test Point Data0 + ground
To Enable Preloader  Mode :
     Method 1    - Just Insert cable
-------------------------------------------------------

Searching for MTK Device...Found
  MTK Port Type   : Flashmode BROM
  FriendlyName    : MediaTek USB Port_V1633 (COM7)
  Device          : /5&15c311e1&0&6
  SymbolicName    : \\?\usb#vid_0e8d&pid_0003#5&15c311e1&0&6#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
  Driver Ver      : 01/22/2015,3.0.1504.0
  Service         : wdm_usb

Openning Port [COM7] Ok
Handshaking...Ok
  HwCode          : 6580 {MT6580}
  Hwver           : 0000
  Target config   : 05
  SBC             : 01 (True)
  SLA             : 00 (False)
  DAA             : 04 (True)
  SWJTAG          : 04 (True)
  EPP             : 00 (False)
  CERT            : 00 (False)
  MEMREAD         : 00 (False)
  MEMWRITE        : 00 (False)
  CMD_C8          : 00 (False)
  Connection      : BROM
  HW Subcode      : 8A00
  HW Subcode      : CA00
  SW Ver          : 0000
  ME_ID           : C4B49E627088DC4B014245EE84E9B4A4

Exploiting Device...
Successfully Exploited..
Handshaking...Ok
Dumping Preloader from Bootrom..
Seeking preloader address..Found @ 0x00200B40
Starting to dump...
Prel Size : 0x0001E6F8
Successfully dump preloader..  [C:\Hydra Tool\Boot\PreloaderDump\preloader_k80_bsp.bin]
  Target config   : 00
  SBC             : 00 (False)
  SLA             : 00 (False)
  DAA             : 00 (False)
  SWJTAG          : 00 (False)
  EPP             : 00 (False)
  CERT            : 00 (False)
  MEMREAD         : 00 (False)
  MEMWRITE        : 00 (False)
  CMD_C8          : 00 (False)
  Connection      : BROM
Uploading legacy da...
DA :MTK_AllInOne_DA_5.2152.bin
Legacy DA2 Patched..
Legacy DA2 CMD F0 is patched.
Successfully uploaded stage 1, jumping ..
Executing JUMP_DA Address @ 0x00200000
Jumping to 0x00200000 Ok
Got loader sync !
Reading Nand Info..
Reading EMMC Info
EMMC_INFO     : 0x00000000
Uploading Stage 2
DRAM config needed for : 51000115413336587DEE034271982ECA
Reading dram nand info ...
Sending dram info ...
RAM-Length:  BC000000
5A
Successfully upload stage 2

Flash and ram info.....
  m_int_sram_ret    : 0x00000000
  m_ext_ram_ret     : 0x00000000
  m_ext_ram_type    : 0x02
  m_ext_ram_chip_select : 0x00
  m_int_sram_ret    : 0x00000000
  m_ext_ram_size    : 0x0000000080000000-2 GB
  Randomid          : 0xEEE0A041D2C130894F2BFD9D0FF66A6D
  m_emmc_ret        : 0x00000000
  m_emmc_boot1_size : 0x0000000000400000-4 MB
  m_emmc_boot2_size : 0x0000000000400000-4 MB
  m_emmc_rpmb_size  : 0x0000000000400000-4 MB
  m_emmc_gp_size[0] : 0x0000000000000000-0 Bytes
  m_emmc_gp_size[1] : 0x0000000000000000-0 Bytes
  m_emmc_gp_size[2] : 0x0000000000000000-0 Bytes
  m_emmc_gp_size[3] : 0x0000000000000000-0 Bytes
  m_emmc_ua_size    : 0x0000000747C00000-29.121 GB
  CID               : 51000115413336587DEE034271982ECA

Checking Connection Speed..
Configuration HighSpeed Switch : True
Full Speed Detected..
Switching To High Speed...
Connected to preloader...
Reconnecting to preloader...
Reading Partition Table ..
Partition Count : 37

Reading IMEI........

IMEI Info....
IMEI1 : 353800********
IMEI2 : 353800********
-------------------------------
Bootloader Status...
  Bootloader : Locked
-------------------------------
Backing up Security..
- preloader(preloader.bin), 512 KB                    = Ok  [preloader_k80_bsp.bin]
  *Creating Scatter file... C:\Hydra Tool\Backup\MTKBKUP\6580_C4B49E6270844KJ014245EE84E9B4A4\Auto\072023147770726\6580_Android_scatter.txt
- pgpt(pgpt.bin), 512 KB                              = Ok
- nvram(nvram.bin), 5 MB                              = Ok
- nvdata(nvdata.bin), 32 MB                           = Ok
- frp(frp.bin), 1024 KB                               = Ok
- protect1(protect1.bin), 10 MB                       = Ok
- protect2(protect2.bin), 10 MB                       = Ok
- persist(persist.bin), 48 MB                         = Ok
- proinfo(proinfo.bin), 3 MB                          = Ok
- seccfg(seccfg.bin), 256 KB                          = Ok
Backup Done!!!

Elapsed Time : 00:01:15

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
                      Service Function
               Factory Reset Protection[FRP]
                            Auto
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Searching for MTK Device...Found
  MTK Port Type   : Flashmode Preloader
  FriendlyName    : MediaTek DA USB VCOM (Android) (COM25)
  Device          : /5&15c311e1&0&6
  SymbolicName    : \\?\usb#vid_0e8d&pid_2001#5&15c311e1&0&6#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
  Driver Ver      : 01/22/2015,3.0.1504.0
  Service         : wdm_usb

Openning Port [COM25] Ok
Reading Partition Table ..
Partition Count : 37

Reading IMEI........

IMEI Info....
IMEI1 : 353800*********
IMEI2 : 353800*********
-------------------------------
Bootloader Status...
  Bootloader : Locked
-------------------------------

Rebooting Device...
Reboot Option : RebootToNormal
Rebooting Operation Done!!!!

Action Result :  Ok

Elapsed Time : 00:00:06