HYDRA Infinix Note 12 X663 Factory Reset (Frp) Remove With Hydra Tool (2 Viewers)

-------------------------------------------------------
To Enable BROM  Mode :
     Method 1    - Bootkey (Vol + - Power) or any combination
     Method 2    - Enable Preloader to brom(crashing Method)
     Method 3    - Test Point Data0 + ground
To Enable Preloader  Mode :
     Method 1    - Just Insert cable
-------------------------------------------------------

Searching for MTK Device...Found
  MTK Port Type   : Flashmode BROM
  FriendlyName    : MediaTek USB Port_V1633 (COM33)
  Device          : /6&3b073303&0&4
  SymbolicName    : \\?\usb#vid_0e8d&pid_0003#6&3b073303&0&4#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
  Driver Ver      : 01/22/2015,3.0.1504.0
  Service         : wdm_usb
Handshaking...
  HwCode          : 0707 {MT6768}
  Hwver           : 0000
  Target config   : E5
  SBC             : 01 (True)
  SLA             : 00 (False)
  DAA             : 04 (True)
  SWJTAG          : 04 (True)
  EPP             : 00 (False)
  CERT            : 00 (False)
  MEMREAD         : 20 (True)
  MEMWRITE        : 40 (True)
  CMD_C8          : 80 (True)
  Connection      : BROM
  HW Subcode      : 8A00
  HW Subcode      : CA00
  SW Ver          : 0000
  ME_ID           : 96B681F220518B4AE134D577C94589D6
  SOC_ID          : B26B5F3A6FD878D62705B35C0225D55D90A2E79F559C384626882DDF0679492F

Exploiting Device...
Successfully Exploited..
Handshaking...Ok
Dumping Preloader from Bootrom..
Seeking preloader address..Found @ 0x00200BC4
Starting to dump...
Prel Size : 0x0005029C
Successfully dump preloader..  [C:\Hydra Tool\Boot\PreloaderDump\preloader_x663_h6915.bin]
  Target config   : 00
  SBC             : 00 (False)
  SLA             : 00 (False)
  DAA             : 00 (False)
  SWJTAG          : 00 (False)
  EPP             : 00 (False)
  CERT            : 00 (False)
  MEMREAD         : 00 (False)
  MEMWRITE        : 00 (False)
  CMD_C8          : 00 (False)
  Connection      : BROM
Sending Da1..
Successfully uploaded stage 1, jumping ..
Executing JUMP_DA Address @ 0x00200000
Jumping to 0x00200000 Ok.. 1
Successfully received DA sync
  ONNECTION_AGENT : brom
  DRAM config needed for : 1501003356364342
Sending auto preloader from dump...  [preloader_x663_h6915.bin]
Sending emi data.. [DRAM setup passed.]
Sending emi data succeeded.
Uploading stage 2...
Patching da2 ...
Hash check not patched. Ok
Error:  on sending data: DA hash mismatch
Upload data was accepted. Jumping to stage 2...
Successfully uploaded stage 2
  ERAM Size       : 0x0000000000070000-448 KB
  IRAM Size       : 0x0000000100000000-4 GB
  EMMC Boot1 Size : 0x0000000000400000-4 MB
  EMMC Boot2 Size : 0x0000000000400000-4 MB
  EMMC RPMB Size  : 0x0000000001000000-16 MB
  EMMC USER Size  : 0x0000001D1EC00000-116.48 GB
  EMMC CID        : 150100335636434242022FF5CCEA290F - 3V6CBB
  HW-CODE         : 0x707
  HWSUB-CODE      : 0x8A00
  HW-VERSION      : 0xCA00
  SW-VERSION      : 0x0
  CHIP-EVOLUTION  : 0x1
  DA-VERSION      : 1.0
  Speed           : high-speed
Executing DA Ext Method 1
Upload data was accepted. Jumping to stage 2...
DA Extensions successfully added
Reading Partition Table ..
Partition Count : 52
--------------- Reading build.prop content ---------------
--------------- end of build.prop content ---------------
-------------------------------
Bootloader Status...
  Bootloader : Locked
-------------------------------
Backing up Security..
- preloader(preloader.bin), 512 KB                    = Ok  [preloader_x663_h6915.bin]
  *Creating Scatter file... C:\Hydra Tool\Backup\MTKBKUP\0707_96B681F220518B4AE134D577C94589D6\Auto\120423021450\0707_Android_scatter.txt
- pgpt(pgpt.bin), 32 KB                               = Ok
- nvram(nvram.bin), 70 MB                             = Ok
- nvdata(nvdata.bin), 64 MB                           = Ok
- frp(frp.bin), 1024 KB                               = Ok
- protect1(protect1.bin), 8 MB                        = Ok
- protect2(protect2.bin), 14.367 MB                   = Ok
- persist(persist.bin), 48 MB                         = Ok
- proinfo(proinfo.bin), 3 MB                          = Ok
- nvcfg(nvcfg.bin), 32 MB                             = Ok
- sec1(sec1.bin), 2 MB                                = Ok
- seccfg(seccfg.bin), 8 MB                            = Ok
Backup Done!!!

Elapsed Time : 00:00:31