Infinix Note 12 X663 Factory Reset (FRP) Remove with Hydra Tool
➢ Pattern Lock And FRP Lock Remove
➢ First Check Preloader mode option (select Prelaoder method Infinix/tecno 1).
➢ Click Boot Info
➢ Select Ultrapower Option (Auto)
➢ Now Remove done
➠ Boot Info
➠ Pattern lock And FRP Remove
➢ Pattern Lock And FRP Lock Remove
➢ First Check Preloader mode option (select Prelaoder method Infinix/tecno 1).
➢ Click Boot Info
➢ Select Ultrapower Option (Auto)
➢ Now Remove done
➠ Boot Info
Code:
-------------------------------------------------------
To Enable BROM Mode :
Method 1 - Bootkey (Vol + - Power) or any combination
Method 2 - Enable Preloader to brom(crashing Method)
Method 3 - Test Point Data0 + ground
To Enable Preloader Mode :
Method 1 - Just Insert cable
-------------------------------------------------------
Searching for MTK Device...Found
MTK Port Type : Flashmode BROM
FriendlyName : MediaTek USB Port_V1633 (COM33)
Device : /6&3b073303&0&4
SymbolicName : \\?\usb#vid_0e8d&pid_0003#6&3b073303&0&4#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
Driver Ver : 01/22/2015,3.0.1504.0
Service : wdm_usb
Handshaking...
HwCode : 0707 {MT6768}
Hwver : 0000
Target config : E5
SBC : 01 (True)
SLA : 00 (False)
DAA : 04 (True)
SWJTAG : 04 (True)
EPP : 00 (False)
CERT : 00 (False)
MEMREAD : 20 (True)
MEMWRITE : 40 (True)
CMD_C8 : 80 (True)
Connection : BROM
HW Subcode : 8A00
HW Subcode : CA00
SW Ver : 0000
ME_ID : 96B681F220518B4AE134D577C94589D6
SOC_ID : B26B5F3A6FD878D62705B35C0225D55D90A2E79F559C384626882DDF0679492F
Exploiting Device...
Successfully Exploited..
Handshaking...Ok
Dumping Preloader from Bootrom..
Seeking preloader address..Found @ 0x00200BC4
Starting to dump...
Prel Size : 0x0005029C
Successfully dump preloader.. [C:\Hydra Tool\Boot\PreloaderDump\preloader_x663_h6915.bin]
Target config : 00
SBC : 00 (False)
SLA : 00 (False)
DAA : 00 (False)
SWJTAG : 00 (False)
EPP : 00 (False)
CERT : 00 (False)
MEMREAD : 00 (False)
MEMWRITE : 00 (False)
CMD_C8 : 00 (False)
Connection : BROM
Sending Da1..
Successfully uploaded stage 1, jumping ..
Executing JUMP_DA Address @ 0x00200000
Jumping to 0x00200000 Ok.. 1
Successfully received DA sync
ONNECTION_AGENT : brom
DRAM config needed for : 1501003356364342
Sending auto preloader from dump... [preloader_x663_h6915.bin]
Sending emi data.. [DRAM setup passed.]
Sending emi data succeeded.
Uploading stage 2...
Patching da2 ...
Hash check not patched. Ok
Error: on sending data: DA hash mismatch
Upload data was accepted. Jumping to stage 2...
Successfully uploaded stage 2
ERAM Size : 0x0000000000070000-448 KB
IRAM Size : 0x0000000100000000-4 GB
EMMC Boot1 Size : 0x0000000000400000-4 MB
EMMC Boot2 Size : 0x0000000000400000-4 MB
EMMC RPMB Size : 0x0000000001000000-16 MB
EMMC USER Size : 0x0000001D1EC00000-116.48 GB
EMMC CID : 150100335636434242022FF5CCEA290F - 3V6CBB
HW-CODE : 0x707
HWSUB-CODE : 0x8A00
HW-VERSION : 0xCA00
SW-VERSION : 0x0
CHIP-EVOLUTION : 0x1
DA-VERSION : 1.0
Speed : high-speed
Executing DA Ext Method 1
Upload data was accepted. Jumping to stage 2...
DA Extensions successfully added
Reading Partition Table ..
Partition Count : 52
--------------- Reading build.prop content ---------------
--------------- end of build.prop content ---------------
-------------------------------
Bootloader Status...
Bootloader : Locked
-------------------------------
Backing up Security..
- preloader(preloader.bin), 512 KB = Ok [preloader_x663_h6915.bin]
*Creating Scatter file... C:\Hydra Tool\Backup\MTKBKUP\0707_96B681F220518B4AE134D577C94589D6\Auto\120423021450\0707_Android_scatter.txt
- pgpt(pgpt.bin), 32 KB = Ok
- nvram(nvram.bin), 70 MB = Ok
- nvdata(nvdata.bin), 64 MB = Ok
- frp(frp.bin), 1024 KB = Ok
- protect1(protect1.bin), 8 MB = Ok
- protect2(protect2.bin), 14.367 MB = Ok
- persist(persist.bin), 48 MB = Ok
- proinfo(proinfo.bin), 3 MB = Ok
- nvcfg(nvcfg.bin), 32 MB = Ok
- sec1(sec1.bin), 2 MB = Ok
- seccfg(seccfg.bin), 8 MB = Ok
Backup Done!!!
Elapsed Time : 00:00:31➠ Pattern lock And FRP Remove